Exactly How to Remove and Change a Tub
Exactly How to Remove and Change a Tub
Blog Article
We've found this article relating to Tools You Need to Install a New Bathtub listed below on the web and decided it made perfect sense to share it with you in this article.
Installing a bathtub isn't specifically brain surgery, however it does require solid plumbing, woodworking, and also often, tiling skills. Replacing an old bath tub with a brand-new one is likewise a moderately hard task. If the old tub is readily accessible, the job can move speedily; if you need to open a wall to eliminate the old tub and also place the new bath tub, the job is much harder. In either case, the task is within a house handyman's skills, although you will certainly need an assistant to move out the old tub and embeded in the new one. See to it you have actually qualified on your own for the work as well as are comfortable trying it. Instead of hiring a specialist to take over a halfway-completed task, it is much better to consider utilizing one before you start. Chances are you might need a specialist plumber to make tube connections.
This article will certainly help you set up a new bath tub in your bathroom if you have actually already gotten a new bathtub and do not need to alter the setup of your previous supply of water pipelines.
Your devices and material list should make up the following:
Removing Old Taps
If you need to change old faucets with new ones as a part of your setup, after that the first thing you need to do is disconnect the supply of water. After doing so, activate the faucets to drain any kind of water remaining in the system. The procedure of getting rid of the existing taps can be rather bothersome due to the limited accessibility that is frequently the situation.
Make use of a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that attaches the supply pipes to the taps. Have a fabric all set for the remaining water that will originate from the pipelines. Once the supply pipes have actually been gotten rid of, use the same tool to loosen up the nut that holds the faucets onto the bath/basin. You will need to stop the solitary faucets from transforming during this process. As soon as the taps have been eliminated, the holes in the bath/basin will certainly need to be cleaned of any old sealing compound.
Prior to going on to fit the brand-new taps, compare the pipeline links on the old taps to the new taps. If the old taps are longer than the new faucets, after that a shank adapter is needed for the brand-new faucets to fit.
Suitable New Touches
If the tails of the new taps are plastic, then you will need a plastic port to avoid damage to the string. One end of the port fits on the plastic tail of the faucet and also the various other end gives a link to the existent supply pipes.
If you need to fit a monobloc, then you will require reducing couplers, which connects the 10mm pipe of the monobloc to the basic 15mm supply pipe.
Next, position the faucet in the mounting opening in the bath/basin making sure that the washers are in place in between the faucet as well as the sink. Secure the tap in position with the maker offered backnut. Once the tap is firmly in position, the supply pipes can be connected to the tails of the faucets. The faucets can either be connected by using corrugated copper piping or with regular tap connectors. The previous kind ought to be connected to the faucet finishes first, tightening up just by hand. The supply pipes can later on be attached to the other end. Tighten up both ends with a spanner after both ends have actually been linked.
Installing the Bath tub
Utilizing both wooden boards under its feet, position the tub in the required setting. The wooden boards are practical in evenly spreading out the weight of the bath tub over the area of the boards as opposed to focusing all the weight onto 4 small factors.
The following goal is to guarantee that the bath tub is leveled all round. This can be achieved by examining the spirit level as well as adjusting the feet on the tub till the spirit level reviews level.
To set up faucets, fit the bottom of the outermost flexible faucet adapter to the suitable supply pipeline by making a compression join; then do the very same for the other tap.
Turn on the water and inspect all joints and also new pipework for leaks and also tighten them if necessary. Fill up the bath tub and likewise examine the overflow electrical outlet and the typical electrical outlet for leaks.
Lastly, take care of the bathroom paneling as described in the maker's user's manual. Tiling and sealing around the tub needs to wait until the bathtub has been made use of at the very least once as this will settle it right into its last position.
Preparing for the Setup
To start with, the sustaining frame supplied with the bath must be fitted (if called for) according to the supplier's instructions. Next, fit the taps or mixer to the tub. When suitable the faucet block, it is necessary to make sure that if the tap comes with a plastic washer, it is fitted between the bath as well as the faucets. On a plastic bathroom, it is additionally reasonable to fit a sustaining plate under the faucets unit to prevent strain on the bathtub.
Fit the flexible tap ports to the bottom of the two taps utilizing 2 nuts as well as olives (often supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and then pass the outlet through the hole in the bath. Use the nut supplied by the manufacturer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the versatile overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which should be fitted inside the bathroom. See to it you make use of every one of the provided washers.
Attach the catch to the bottom of the waste electrical outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Attach all-time low of the overflow tube in a similar manner.The bath should currently prepare to be fitted in its final position.
Tiling Around the Bath tub
In the location where the bathroom satisfies the tile, it is necessary to secure the accompanies a silicone rubber caulking. This is essential as the fitting can relocate sufficient to split a rigid seal, causing the water to pass through the wall surface between the bath and also the tiling, causing problems with dampness and also feasible leaks to the ceiling listed below.
You can select from a selection of coloured sealers to blend in your fixtures and installations. They are marketed in tubes as well as cartridges, and are capable of securing voids as much as a width of 3mm (1/8 inch). If you have a bigger void to fill, you can load it with spins of soaked newspaper or soft rope. Bear in mind to constantly fill the bathtub with water prior to sealing, to allow for the activity experienced when the bathtub is in usage. The sealant can fracture rather very early if you do not take into consideration this motion before securing.
Conversely, ceramic coving or quadrant ceramic tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are likewise easily readily available on the market. It is suggested to fit the ceramic tiles using waterproof or water resistant glue as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I hope you liked our excerpt about Installing A Bathtub. Thanks a ton for finding the time to read through our piece of content. Sharing is good. You never know, you may very well be doing someone a favor. I love reading our article about A Step-by-Step Guide to Installing a Bathtub.
Visit Site
Report this page